tiras LED Engineering Selection Handbook
Compare SOB, roll-to-roll, high-density, bañadores de pared and ultra-long tiras LED selection criteria and engineering parameters.
01 / SOB · Continuous optical line
SOB utiliza LEDs encapsulados individualmente, con conexiones internas mediante hilo de oro, soldados a un circuito flexible bajo una capa óptica continua de silicona. Esto difiere del COB con chips sin encapsular bajo una capa compartida de fósforo.
Selection matrix
| Project condition | Selection direction | Check before specifying |
|---|---|---|
| Shallow profile, visible light line | SOB con un difusor adecuado | Profundidad del perfil, ángulo de observación y visibilidad de los puntos en una muestra |
| Colour-critical display | SOB con la opción de reproducción cromática requerida | Model-specific CRI, binning and CCT |
| Extended continuous installation | SOB-R2R or constant-current SOB where offered | Continuous circuit length, feed layout and powered-run limit |
Parameter comparison
| Parámetro | Options or construction | Engineering decision |
|---|---|---|
| Emitter architecture | SOB: packaged LEDs / COB: bare dies | Select by package construction, not visual similarity alone |
| Optical surface | Continuous silicone layer / model-specific diffuser | Confirme la apariencia en el perfil de montaje real |
| Electrical design | Voltage and current method vary by model | Lea la ficha del producto antes de dimensionar las alimentaciones y los drivers |
Packaging type alone does not establish an IP rating, run length, lifetime or performance guarantee.
View products02 / R2R · Continuous circuit
DENO fabrica tiras SMD-R2R y SOB-R2R sobre circuitos flexibles con deposición electrolítica continua. R2R describe el proceso de fabricación del circuito; no garantiza que una sola alimentación pueda alimentar una bobina completa.
Selection matrix
| Project condition | Selection direction | Check before specifying |
|---|---|---|
| Few accessible splice locations | Continuous R2R circuit | Specified unspliced circuit length and cut points |
| gran longitud with uniform appearance | Circuito R2R con una alimentación adecuada o un diseño de corriente constante | caída de tensión, actual load and far-end output |
| SOB optical line plus continuous circuit | SOB-R2R variant | Tanto el encapsulado como la construcción del circuito del modelo seleccionado |
Parameter comparison
| Parámetro | Options or construction | Engineering decision |
|---|---|---|
| Circuit fabrication | Continuous electroplated web / joined die-cut panels | Check intermediate splice count within the ordered length |
| Copper construction | 35 µm base + 70 µm electroplated = 105 µm on specified builds | Confirme la construcción de cobre del modelo concreto |
| Run planning | Circuit length / powered run / supplied reel length | Treat these as three separate specifications |
La longitud continua del circuito, la longitud del tramo alimentado y la longitud de la bobina son valores diferentes. No deduzca uno a partir de otro.
View products03 / alta densidad · Pitch and diffusion
Las tiras de alta densidad reducen la separación entre los LEDs encapsulados. La visibilidad de los puntos depende conjuntamente del paso entre LEDs, la profundidad del difusor, la transmitancia del difusor y el ángulo del haz.
Selection matrix
| Project condition | Selection direction | Check before specifying |
|---|---|---|
| Close-viewed joinery | Modelo de paso más corto con un difusor adecuado | Montaje de prueba a la distancia de observación prevista |
| Shallow aluminium channel | Compare SMD de alta densidad con una opción de línea continua | Channel depth, diffuser type and installed appearance |
| Colour-sensitive display | Modelo de alta densidad con reproducción cromática y clasificación por bins especificadas | Product-specific CRI, CCT and binning |
Parameter comparison
| Parámetro | Options or construction | Engineering decision |
|---|---|---|
| LED pitch | Shorter / longer spacing | Compare los valores reales de LED/m y el paso de los modelos candidatos |
| Profile depth | Shallow / deeper cavity | Compruebe el solapamiento a la distancia real del difusor |
| Diffuser | Higher / lower transmittance | Balance dot control against delivered light |
La densidad de LEDs por sí sola nunca garantiza una instalación sin puntos visibles; pruebe conjuntamente el perfil y el difusor especificados.
View products04 / bañadores de pared · Beam and setback
Los bañadores de pared flexibles utilizan ópticas secundarias para dirigir la luz sobre una superficie arquitectónica. La iluminación rasante y el bañado de superficies requieren diferentes formas de haz y geometrías de montaje.
Selection matrix
| Project condition | Selection direction | Check before specifying |
|---|---|---|
| Reveal surface texture | Narrow-beam grazing arrangement | Setback, aiming, surface finish and mock-up |
| Evenly light a wall | Wider or asymmetric washing arrangement | Beam angle, setback and illumination uniformity |
| Outdoor or wet location | Modelo y sellado seleccionados según la exposición | Exact model IP rating, end seals and site water exposure |
Parameter comparison
| Parámetro | Options or construction | Engineering decision |
|---|---|---|
| Optical task | Grazing / washing | Choose texture emphasis or even vertical illumination first |
| Lens | 15° / 30° / 60° options on applicable models | Confirm model availability and photometry before specifying |
| Ingress exposure | IP65 water jets / IP67 temporary immersion | One rating does not automatically establish the other |
La uniformidad del haz depende de la lente, la distancia de montaje y la superficie. Los grados de protección IP son específicos de cada modelo e instalación.
View products05 / Ultra-long · Power distribution
Long-run strip selection separates circuit construction from power distribution. Per-segment linear constant-current designs can help regulate output within their specified electrical limits.
Selection matrix
| Project condition | Selection direction | Check before specifying |
|---|---|---|
| Feed available at one end | Compruebe un modelo apto para la longitud de tramo requerida con alimentación por un solo extremo | W/m, caída de tensión and far-end brightness |
| Feeds available at both ends | Compare both-end feeding with single-end feeding | Driver capacity and effective feed distance |
| Concealed middle access | Mid-strip tap where permitted by the model | Segment wiring, polarity and actual installation layout |
Parameter comparison
| Parámetro | Options or construction | Engineering decision |
|---|---|---|
| Control method | Constant voltage / per-segment corriente constante | Confirm driver and strip compatibility |
| Feed position | Single end / both ends / mid-strip tap | Both-end or central feed can reduce farthest feed distance to L/2 |
| Supply | 24 V / 36 V / 48 V on applicable models | Verifique el modelo seleccionado, la carga y el driver antes de dimensionar el tramo |
No existe una longitud máxima universal de tramo alimentado: determínela para el modelo, la tensión, la carga y la topología de alimentación seleccionados.
View products